How do I measure for a replacement toilet seat UK?

Measure your existing toilet seat for the correct measurements or, if you’re measuring a new toilet with no seat, measure the length from the middle of the fitting holes to the centre of the front of your toilet bowl. Then measure the width from the widest point across.

Measure the length of the bowl from between the seat bolts to the outside edge of the front of the bowl. If you have a round bowl, this dimension should be about 16.5 inches. If you have an elongated bowl, the measurement should be around 18 to 18.5 inches.

One may also ask, which is better plastic or wood toilet seats? Wood Toilet Seat is a little heavier than plastic seat. If your family members are much healthier then wood seat is more convenient for your toilet. Both the wood and plastic seats are durable for everyday use. You should prefer plastic seat if you want a lightweight toilet seat.

Correspondingly, are all toilet seats the same size UK?

No, not all toilet seats fit the same because toilets come in a variety of different shapes, so you’ll need to check yours before buying. There are three types of toilet shapes commonly found in UK homes. Most toilet seats are an oval shape, although some may be more of a contemporary square or D-shape.

Do toilet seats fit all toilets?

Toilets come in different shapes and sizes and so do toilet seats. To find the right seat you first have to work out what shape your pan is. You should be able to tell just by looking at your toilet what shape it is, this is even easier if the toilet seat is already attached.

Can I put an elongated seat on a round toilet?

You can install the elongated seat on top of the round toilet but you run the risk of it snapping or moving around on you at where it screws in because the pressure won’t be evenly applied around the seat.

Are all toilet seats the same size?

Toilet seats don’t come in sizes, but they do come in two different shapes: round toilet seats and elongated toilet seats, each of which correspond to two different toilet bowl shapes. Round toilet seats are still the standard in most homes, and they’re the toilet seats you typically see most often.

Do all toilets fit the same?

Most toilets will have a 12 inch rough-in. If you’re replacing an existing toilet, look for a replacement toilet with the same rough-in. A toilet with a larger rough-in measurement will require you to change your plumbing configuration or move the wall to get the toilet to fit.

How far should a toilet be from a wall?

Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.

Are toilet seats easy to replace?

Installing a new toilet seat is an easy DIY project. Whether you’re replacing yours because it’s old, or because you just want a new style, all you need are some basic tools and a few minutes. Unbolt the old seat, then pop the new one in place using the hardware included in your new toilet seat’s box.

How do quick release toilet seats work?

The soft close hinge works with the seat and the lid to help stop them dropping too quickly. The seat is in a white plastic. The quick release mechanism makes cleaning easy.

How do you replace a toilet UK?

Fitting the new toilet Assemble and fit the flush mechanism and inner parts of the cistern. Attach the close-couple washer to the top of the pan. Secure the cistern to the pan by hand tightening the supplied washers and wing nuts onto the bolts. Insert the pan connector to the waste pipe, making sure the fit is snug.

What is the standard size of a toilet?

Standard toilet dimensions are typically between 28–30″ deep, roughly 20″ wide, between 27–32″ high, and have a rough-in between 10–14″.

What is the standard size toilet seat?

There are industry standards for toilet seats – all toilets have seat post holes on 5 1/2″ centers – all elongated bowls are 18 1/2″ from seat posts to front of rim, and all round bowls are 16 1/2″. Any manufacturer’s seats will fit any toilet manufacturers bowls if they are standard round or standard elongated.

How do I know if my toilet is round or elongated?

it’s a noticeable difference. If you’re still wondering, you can measure from the two mounting bolts at the seat hinge to the very front of the toilet bowl. That measurement will be about 16 1/2 inches if the bowl is round, and 18 1/2 inches if your bowl is elongated.

Should a toilet seat overhang?

The Swash may extend slightly over the front edge of your toilet bowl. Measure the distance from the front of the toilet tank to the front of the toilet bowl. A distance less than 19.4 inches from the tank to the front of the toilet bowl will also cause overhang.